Hanging curtains in an apartment means using methods that do not damage walls or leave permanent marks
The core rule is this: your landlord can charge you for wall damage when you move out, so you need to hang curtains in a way that leaves the wall in its original condition. That means no nails, no screws, and no adhesive that will peel paint. The methods that work are tension rods (which rely on pressure rather than fasteners), adhesive hooks rated for your wall type, and damage-free picture hanging strips.
Before you hang anything, check your lease. Some leases restrict what you can do to walls; others say nothing. If your lease is silent, you still owe the landlord a wall in move-out condition. The safest approach is to ask your landlord or property manager in writing which methods they permit. That email becomes your proof if a damage charge appears later.
Key Takeaways
- Tension rods need no fasteners at all and work in most window frames, but they require the right width for your window and may not support heavy curtains.
- Adhesive hooks and picture hanging strips leave no holes if removed slowly and at a low angle, but they fail on textured walls and require the wall to be clean and dry before installation.
- Command hooks and similar removable fasteners are made to release without damage, though weight limits vary by product and must match your curtain weight.
- Ask your landlord which method is permitted before you install anything, and keep the receipt or packaging so you can remove the hardware the same way you put it up.
Tension rods: no holes, no adhesive, pressure only
A tension rod is a spring-loaded bar that expands to fit snugly inside your window frame. You measure the width of the inside of your frame, buy a rod that adjusts to that width, and twist the ends to tighten it until it holds firm. No nails, no screws, no holes. When you move out, you untwist it and take it with you.
Tension rods work best on standard rectangular windows where the frame is solid and the rod can rest on the frame itself. They do not work on windows with deep sills, curved frames, or frames too narrow to grip. They also have weight limits — most standard tension rods hold 5 to 10 pounds, so they work for lightweight curtains or sheers but not for heavy blackout curtains or multiple layers.
The main drawback is that tension rods are visible. The rod itself shows, and the curtains hang from the rod rather than from the wall above the window. If your window treatment needs to look finished or to cover the frame completely, a tension rod may not give you that look. But for renters, the trade-off is worth it: zero damage, zero deposit risk.
Adhesive hooks and picture hanging strips for drywall
Adhesive hooks stick to the wall with a strong adhesive backing. The most common brand is Command, which makes hooks in different sizes and weight ratings. You clean the wall with a dry cloth, press the hook firmly for 30 seconds, wait one hour for the adhesive to set, then hang your curtain rod on the hook. When you leave, you remove the hook by pulling the tab slowly at a low angle — the adhesive releases without tearing the paint.
Picture hanging strips work the same way: two strips of adhesive-backed fabric that grip a picture frame or rod. They come in different weight ratings, usually 5 to 16 pounds per pair. You stick one strip to the wall and one to the back of your curtain rod, press them together, and the rod hangs without any fastener going into the wall.
Both methods fail on textured walls, glossy paint, or walls that are dirty or damp. If your wall is textured (popcorn, orange peel, or heavily bumpy), the adhesive cannot make full contact and will not hold. If the wall is wet or humid, the adhesive will not cure properly. Clean the wall with a dry cloth and let it dry completely before you install anything. Do not use these on walls painted with high-gloss or semi-gloss paint — the adhesive will not grip. Flat or matte paint works best.
Weight limits and choosing the right fastener for your curtains
Before you buy hooks or strips, weigh your curtains or estimate their weight. A single panel of lightweight curtain fabric weighs 1 to 3 pounds. Blackout curtains weigh 3 to 6 pounds per panel. If you are hanging two panels, double that weight. Add the weight of the rod itself — most standard rods weigh 1 to 3 pounds.
Once you know the total weight, buy fasteners rated for at least that weight, ideally with a safety margin. A hook rated for 10 pounds should hold 10 pounds, but it is safer to use a 16-pound hook if you are hanging 10 pounds of curtains. The rating is the maximum safe load, not the recommended load.
If your curtains are heavier than the adhesive fasteners can hold, you have two options: use a tension rod instead, or ask your landlord whether you can use a single small nail or screw. Many landlords will permit one or two small holes if you patch them with spackle when you move out. Get that permission in writing.
Installation steps for adhesive hooks and strips
Measure the height where you want the rod to hang. Standard practice is to hang the rod 4 to 6 inches above the window frame, or higher if you want the curtains to look taller. Mark the spot lightly with a pencil.
Clean the wall with a dry cloth. If there is dust, dirt, or residue, wipe it away. Let the wall dry completely — do not install adhesive hooks on a damp wall.
Remove the backing from the adhesive hook or strip and press it firmly to the wall at your marked spot. Hold it for 30 seconds with steady pressure. Do not let go and come back — the adhesive needs continuous pressure to set properly.
Wait one hour before you hang anything on the hook. The adhesive needs time to cure. If you hang the rod when ready, the hook may pull away from the wall.
Hang your curtain rod on the hook. If you are using picture hanging strips, stick one strip to the wall and one to the rod, then press them together firmly for 30 seconds.
Removing hooks and strips without damaging the wall
When you move out, do not pull the hook straight out or yank it away from the wall. That will tear the paint or the drywall. Instead, locate the small tab or edge of the adhesive backing and pull it slowly at a low angle — almost parallel to the wall — toward the corner of the room. The adhesive will release gradually without tearing.
If the hook is stuck and will not budge, use a hair dryer on low heat to warm the adhesive for 30 seconds, then try again. Heat softens the adhesive and makes it release more easily.
After you remove the hook, there may be a small residue of adhesive left on the wall. Rub it gently with your finger or a soft cloth — it will ball up and come off. Do not use a scraper or anything abrasive, which will damage the paint.
What to do if your window frame will not hold a tension rod
If your window is too wide, too narrow, or has a frame that will not grip a tension rod, you have three options. First, ask your landlord whether you can use a single small nail or screw — many will permit this if you patch the hole with spackle when you move out. Second, use adhesive hooks or picture hanging strips on the wall above the window instead of inside the frame. Third, use a freestanding curtain rod stand, which is a weighted base that holds a rod without any fastening to the wall or window.
A freestanding stand is the most damage-free option if your window does not work with a tension rod. The stand sits on the floor or on a shelf, and the rod rests in the stand. When you move out, you take the whole thing with you. The downside is that it takes up floor space and may not look as finished as a wall-mounted rod.
Frequently Asked Questions
Can I use nails or screws if I patch the holes when I move out?
Patching holes with spackle is the standard way to repair nail holes, and most landlords accept it as normal wear. However, your lease may forbid nails entirely, or your landlord may have a different standard. Ask in writing before you drill. If you do use nails, use the smallest size that will hold your rod, patch the holes with spackle that matches your wall color, and sand it smooth when it dries.
Will adhesive hooks damage textured walls?
Adhesive hooks do not grip textured walls well because the adhesive cannot make full contact with the bumpy surface. The hook may hold for a while but will eventually pull away. Tension rods or a freestanding stand are better choices for textured walls. If you must use adhesive, test it on a small, inconspicuous spot first.
How much weight can a tension rod hold?
Most standard tension rods hold 5 to 10 pounds. Check the packaging or product description for the weight limit of the specific rod you buy. If your curtains are heavier, you need a heavier-duty tension rod or a different hanging method.
What if I remove an adhesive hook and it tears the paint?
Small paint tears are usually considered normal wear and tear, especially if you removed the hook correctly. If the tear is large or the landlord charges you for it, document it with photos and ask the landlord to show you the damage in the lease's move-out inspection. Keep your receipt for the hooks and the Command removal tab as proof you used the product as intended.
Can I use adhesive hooks on painted brick or concrete?
Adhesive hooks do not work on brick or concrete because the surface is too porous and uneven. Tension rods are your best option if your window frame is solid enough to grip one. If not, ask your landlord whether you can use a small screw or anchor designed for masonry.